1、將開齒穿條機設備的電源線接到車間內380伏的空氣開關上，檢查電路接好從左邊數，左邊的三根黑色的是380伏火線、左邊第四根黃色的是零線。通電后如果發現“刀盤上升”是反的，那么要將左邊的三根黑線任意交叉換一下。調解好電機的方向。

　　1. Connect the power cord of the gear threading machine equipment to the 380V air switch in the workshop, check the circuit connection, and count from the left. The three black wires on the left are 380V live wires, and the fourth yellow wire on the left is neutral wire. If it is found that the "cutter head rising" is reversed after power on, then the three black lines on the left should be crossed and replaced at will. Adjust the direction of the motor.

　　2、調解和安裝好兩面的托料平臺。

　　2. Mediate and install the material platform on both sides.

　　3、先放入一根型材，用手調解該機頭的左右挪動手輪，將“導向定位塊”調解到機器出條槽口和鋁型材穿條槽口一致;如需要上下調解則按動“刀盤上升”和“刀盤下降”來調解機頭的高度。

　　3. First, place a profile and manually adjust the left and right movement handwheel of the machine head to align the "guide positioning block" with the machine strip slot and the aluminum profile strip slot; If you need to adjust the height of the machine head up and down, press "cutterhead up" and "cutterhead down" to adjust the height of the machine head.

　　4、再放入上面的兩根開好齒的鋁型材，調解后面托料架子上的“定位板”，頂住鋁型材。

　　4. Insert the two toothed aluminum profiles on top and adjust the "positioning plate" on the material rack at the back to support the aluminum profiles.

　　5、用人工將隔熱條順導向槽口送入鋁型材槽口內一點。

　　5. Manually guide the insulation strip into the slot of the aluminum profile to a certain point.

　　6、踩下設備上的腳踏開關，齒刀加壓轉動，將隔熱條高速送入鋁型材槽口，穿條完畢后，松開腳踏開關。

　　6. Step on the foot switch on the device, apply pressure and rotate the toothed knife, and quickly feed the insulation strip into the slot of the aluminum profile. After threading the strip, release the foot switch.

　　7、重復以上步驟，加工下一根鋁型材。

　　7. Repeat the above steps to process the next aluminum profile.

　　本文由 開齒穿條機  友情奉獻.更多有關的知識請點擊  http://www.mmssii.com   真誠的態度.為您提供為多維度的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from the open tooth threading machine. For more related knowledge, please click http://www.mmssii.com Sincere attitude. We provide you with comprehensive services. We will gradually contribute more relevant knowledge to everyone. Please stay tuned